Aga-ranges GC Instrukcja Użytkownika Pobierz pdf

NOTE: THESE INSTRUCTIONS SHOULD BE LEFT

WITH THE APPLIANCE AND THE USER TO RETAIN

FOR FUTURE REFERENCE.

Aga Gas Fired ranges are delivered unassembled.

Before installation can be made the site is inspected for

suitability by an Authorised Aga Distributor and corrected

where necessary to conform with local installation codes

or in the absence of local codes with:

In Canada:

The CAN/CGA-B149 installation codes.

In U.S.:

The National Fuel Gas Code ANSI Z223. 1-latest edition.

Assembly is undertaken on site by the same Aga

Distributor to ensure correct performance and safety.

It is essential that the base or hearth on which the range

stands should be level and strong enough to support the

weight of the range.

Approximate weights:-

Models GC (Open Flue) and GC (Direct Vent)

- 408kg (900lb)

Models GE (Open Flue) and GC (Direct Vent)

- 585kg (1290lb)

The top face of the hearth must be of non-combustible

material for a minimum thickness of 12mm (1/2in) and

comply with current Building Regulations and National

Fire Laws.

The wall behind the cooker draft hood and flue connector

must have a minimum air gap of 57mm (2 1/4”). Any

openings in the wall behind the range or in the floor under

the range must be sealed before appliance installation.

Ensure the draft hood is securely bolted to the support

spigot as shown in Fig. 2.

NOTE: THIS IS NORMALLY FITTED AND SECURED BY

THE FACTORY BEFORE DESPATCH.

The wall behind the range must be the outside wall for

the venting of flue products. Wall thickness between

150mm (6 in) and 355mm (14 in) can be catered for at the

same time as site inspection.

Alternatively, special lengths can be offered to order up to

a maximum of 610mm (24 in) long.

Open Flue - Models GC and GE

Installation Instructions for Aga Gas Fired Range

Models: GC Open Flue Range (2 Oven)

GC Direct Vent Range (2 Oven)

GE Open Flue Range (4 Oven)

GE Direct Vent Range (4 Oven)

For U.S. and Canadian Markets

1 04/08 EINS 33644

BASE OR HEARTH

OPEN FLUE RANGE -

MODELS GC AND GE

DIRECT VENT RANGE-

MODELS GC AND GE

1 2 3 4 5 6 7 8

Podsumowanie treści

Strona 1

NOTE: THESE INSTRUCTIONS SHOULD BE LEFTWITH THE APPLIANCE AND THE USER TO RETAINFOR FUTURE REFERENCE.Aga Gas Fired ranges are delivered unassembled.Be

Strona 2 - VENT CONNECTION

2A 100mm (4in) Type B Gas Vent must be used and fastenedby screw to the draft hood flue collar.U.S.The gas vent must be connected to a chimney orindep

Strona 3 - WALL TILING

3the appliance and should not be less than (4in) internal diameter.7. In the event of an extractor fan being fitted in the vicinity ofthe range, compe

Strona 4 - LOCATION OF NAME PLATE

GC, GE Open Flue ModelsMaximum Heat Input: 4.4kw (15,000 (Btu/h)GC, GE Direct Vent ModelsThe appliance and its individual shut-off valve must bediscon

Strona 5 - INITIAL LIGHTING OF RANGE

In a cold range, difficulty may be experienced in maintainingthe main burner alight on initial light-up only. Should thisoccur, set the control knob t

Strona 6 - TECHNICAL SPECIFICATION

NOTE: DO NOT ATTEMPT TO SERVICE THE RANGEYOURSELF. CONTACT YOUR LOCAL AGA DISTRIBUTORSTATING THE MODEL AND SERIAL NUMBER TOGETHERWITH YOUR NAME AND AD

Strona 7

7Fig. 12 Pilot/Thermocouple DESN 512827

Strona 8 - YEARLY SERVICE

It is recommended that the range be serviced at regular annualintervals.Arrange with the householder that the range has been turnedOFF the night befor

Komentarze do niniejszej Instrukcji

Brak uwag

Aga-ranges GC Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Płyty grzewcze Aga-ranges GC. Aga Ranges GC User Manual Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Płyty grzewcze Aga-ranges GC